Richbetter tachometric controls bldc motor troubleshooting for inconsistent speed and signal noise issues

In high-precision industrial applications, BLDC motors must deliver stable speed control and clean feedback signals. However, inconsistent speed and signal noise remain common issues, especially when motors are integrated into complex systems like semiconductor equipment, robotics, medical devices, or precision grinding machines. Inconsistent speed can show up as jitter, sudden RPM drops, or unstable acceleration, while signal noise often appears as irregular encoder pulses or false feedback, which can lead to oscillation, hunting, or even motor stall. For engineers working with tachometric controls, understanding the root causes and using structured troubleshooting methods is essential to restoring stable operation.

Richbetter Technology specializes in precision drive systems and offers a range of BLDC motors, drivers, and encoder modules designed for demanding industries. Their products are built to integrate tightly with control systems, and their high-performance design aims to reduce common issues. Yet, even high-quality systems can encounter instability due to installation environment, wiring, grounding, or parameter configuration. This article provides a complete troubleshooting guide to resolve inconsistent speed and signal noise problems, aligned with Richbetter’s technical strengths and real-world application contexts.

Why inconsistent speed occurs in tachometric control systems

Tachometric control relies on accurate speed feedback from the motor’s encoder or resolver. The controller uses this feedback to adjust current and PWM duty cycle to maintain target speed. Inconsistent speed typically results from:

• Poor encoder signal integrity

• Excessive electrical noise (EMI) in the feedback loop

• Incorrect driver parameters (PID tuning, current limit, PWM frequency)

• Mechanical factors (misalignment, bearing wear, shaft runout)

• Power supply instability

According to industry studies on servo systems, more than 40% of speed instability cases are caused by feedback signal degradation rather than motor hardware failure. Therefore, addressing encoder and wiring quality should be the first step in troubleshooting.

Step 1: Verify encoder signal quality before changing parameters

Before tuning controllers, confirm the encoder signal is clean and stable. Tachometric control depends on accurate pulse count and timing. The following checks are essential:

Check encoder wiring and connector integrity

Poor wiring can introduce noise and reduce signal amplitude. Ensure:

• Encoder cables are shielded and grounded at one end

• Connectors are tight and corrosion-free

• No cable twisting or sharp bending near the connector

• No nearby high-current cables running parallel

Measure signal amplitude and waveform

Use an oscilloscope to verify:

• Consistent square wave signals

• Correct voltage levels (TTL or differential depending on encoder type)

• No missing pulses or jitter

• No high-frequency spikes indicating EMI

If the waveform is distorted or noisy, the controller will misread speed, leading to inconsistent RPM and hunting behavior.

Step 2: Reduce EMI and signal noise at the source

In industrial environments, EMI is one of the most common causes of signal noise. Motor windings, inverters, and power switching generate electromagnetic interference that can corrupt encoder signals.

Implement grounding and shielding correctly

A frequent mistake is grounding both ends of the shielded cable, which can create ground loops and increase noise. The recommended approach is:

• Ground the shield at the controller end only

• Keep the encoder cable away from power lines

• Use twisted pair and differential signal encoders where possible

Add filtering and isolation

Noise suppression can be improved by:

• Adding ferrite beads on encoder cables

• Using differential line receivers

• Adding low-pass filters to encoder signals (only if allowed by system requirements)

• Using optical isolation between encoder and controller if needed

A study in industrial motor control highlights that proper shielding and grounding can reduce encoder noise by up to 60%, significantly improving speed stability.

Step 3: Inspect mechanical alignment and load factors

Even with clean signals, mechanical issues can create inconsistent speed. Tachometric controls respond to actual speed, so any mechanical instability will be reflected as speed variation.

Check coupling alignment

Misalignment between motor and load can cause vibration and uneven torque, leading to inconsistent speed. Verify:

• Coupling runout is within tolerance

• Shaft ends are aligned

• No excessive axial or radial load

Inspect bearings and rotor balance

Worn bearings or unbalanced rotors cause vibration, which can lead to slight speed variations and can also introduce noise in the encoder.

Step 4: Optimize driver parameters and control loops

Once signal and mechanical factors are verified, fine-tune the driver settings. Many speed instability issues are resolved by adjusting:

PID tuning for speed loop

If the PID parameters are too aggressive, the system will overshoot and oscillate. If too conservative, it will lag behind the setpoint. Start with:

• Lower proportional gain

• Increase integral gain gradually

• Set derivative gain carefully to avoid amplifying noise

Set appropriate PWM frequency and current limit

High PWM frequency increases switching noise but improves torque smoothness. If the system is noisy, consider:

• Reducing PWM frequency slightly

• Ensuring current limits are not too low, which causes speed drop under load

Richbetter’s drive systems are designed for high-performance applications, so proper tuning is crucial for stable operation.

Step 5: Verify power supply stability and system integration

Power supply issues are often overlooked. Voltage fluctuations, insufficient current capacity, or unstable DC bus voltage can cause sudden speed drops.

Check supply voltage ripple and transient response

Use an oscilloscope to measure:

• Voltage ripple under load

• Transient dips when load increases

• DC bus stability

If the power supply cannot provide sufficient current, the driver will reduce torque, causing speed inconsistency.

Confirm proper integration with system controllers

In complex systems like robots, semiconductor equipment, or medical devices, multiple control loops interact. Ensure:

• The motor controller is not receiving conflicting commands

• Speed setpoints are stable

• Communication signals (CAN, EtherCAT, etc.) are clean and error-free

Quick reference checklist for troubleshooting

FAQ

Q1: Why does the motor speed fluctuate only under load?
A: Under load, current demand increases and any power supply or driver limit issues become visible. Check supply stability and current limits.

Q2: Can signal noise be fixed without replacing the encoder?
A: Yes. Most noise issues are caused by wiring, grounding, or EMI. Use shielded cables, ferrite beads, and correct grounding practices.

Q3: How do I know if the issue is mechanical or electrical?
A: If speed instability correlates with vibration or noise, it may be mechanical. If instability appears only when switching on or under electrical noise sources, it is likely electrical.

Conclusion

Inconsistent speed and signal noise in BLDC tachometric control systems are often the result of multiple interacting factors rather than a single defect. A systematic troubleshooting approach—starting from encoder signal integrity, then addressing EMI and grounding, followed by mechanical alignment and driver tuning—can significantly reduce downtime and restore stable performance. Richbetter’s high-quality BLDC motors and precision drive systems provide a strong foundation, but real-world stability depends on proper integration, wiring discipline, and parameter optimization. By following these steps, engineers can ensure reliable speed control, minimize signal noise, and maintain consistent performance in demanding industrial environments.

www.rbtmotion.com
Shenzhen Richbetter Technology Co.,Ltd.

About Author

admin

See author's posts